VinylFrog gloss black taillight tint gives your rear lights a deep, dark smoked look while keeping brake lights, turn signals, and reverse lights fully visible. The high-gloss finish reflects light like wet paint when the car is off, but the film itself maintains 43% light transmission so your lamps do their job.
The air-channel paper liner pushes trapped air out during installation, so you are not fighting bubbles. Clean the lens, apply with a squeegee, trim the edges, and you are done. The adhesive is repositionable, which means you can slide it around to get the alignment right before pressing it down. A self-healing topcoat closes minor wash marks and light scratches with heat exposure.
Maintenance is simple. Use a mild, alcohol-free cleaner and a soft microfiber cloth. Skip the harsh chemicals and abrasives. Built to handle weather, UV, and road grit, this film holds up from -50°C to 110°C and lasts one year under vertical exposure. Removes cleanly with gentle heat when you are ready for a change.
Key Features
Deep Black Smoked finish: dark, sleek look that enhances the rear of your vehicle
Eco-friendly high-grade film: durable and weatherproof
Heat, UV, and scratch resistant: protects lenses from sun damage and daily wear
Self-healing technology: erases minor marks with heat
Repositionable acrylic adhesive: slide and adjust during install. Bonds securely
Dry application: no slip solution. Clean and simple
Finshes: Deep Gloss Black, Smoked
Protective liner: keeps film safe until application
Light Output Note: At the listed VLT, this film allows enough light to pass through for safe, legal use on public roads.
Video
Proper Installation
If the taillight surface is clean and undamaged before installation, the wrap adheres evenly and removes smoothly.
Proper Removal Technique
Using gentle heat (like a heat gun or hairdryer) softens the adhesive, making it easier to peel without pulling or tearing the headlight’s factory coating.
Warning
If the Taillight are already oxidized, yellowed, or have weak factory coating, peeling the wrap can pull off clear coat or cause flaking.
Physical Properties
Classification
Unit
Spec
Remark
Thickness
Top protected film
um
25±5
PE
Acrylic Adhesive
um
20±2
Solvent-based
Face Film
um
100±5
/
Release liner
um
180±2%
Paper Liner
Surface
-
-
Glossy & Matte
/
Width
-
cm
30/40±0.01%
1ft/1.3ft
Length
-
m
10±1%
32ft
Physical Performance
Features
Test Method
Results
Gloss (60°)
GB 8807
92.3
VLT
/
87%
Self-healing Layer Elongation at Break
GB/T 1040.1
112
Face Film Elongation at Break
GB/T 1040.1
309.5
Tear Strength
GB/T529
92.7 KN/m
Tensile Strength
GB/T 1040.1
21.6 Mpa
100% Modulus
GB/T 1040.1
9.1 Mpa
Anti-yellowing
/
ΔE< 1.2
Light Transmission
>40%
43%
Adhesive residue
/
<3%
Release force (N/25mm)
paste on steel board, 90° 26℃ and 60%, GB2792
0.16
Initial tack (g/25mm)
under 24℃ and 26%, GB31125-2014
860
Peel Strength (N/25mm)
180°
15
Holding power(h)
paste on steel board, hang on by 25mm*25mm*1kg weight under 29℃ and 55%, GB/T4851-1998
No peel off within 48 hours
Aging Test
65℃ and 7 days
No adhesive residue under 20 times wrapping
Application Temperature
/
+20℃ to +30℃
Service Temperature
/
-50℃ to +110℃
Recommended Shelf Life
72°F (22°C) and 50% RH
1 year
Durability
/
1 year
Time limits
Must use it within 3 months after receiving the wrap film
3 months
Shelf Life
1 year from date of purchase when stored at 50°F to 80°F (15°C – 25°C) and 45% to 50% relative humidity. Optimum recommended storage conditions are 72°F (22°C) and 50% relative humidity.
Important Notice
The physical properties of the product detailed in this document are based on tests that we believe to be reliable. They are intended only as a source of information and are given without guarantee. They do not constitute a warranty. Purchasers should independently assess the suitability of this material for their specific use prior to application.
Warranty, Limited Remedy, and Disclaimer
Unless an additional warranty is specifically stated on the applicable product packaging or literature, VinylFrog warrants that each product meets the applicable specifications at the time of shipment. We make no other warranties or conditions, express or implied, including but not limited to any implied warranty or condition of merchantability or fitness for a particular purpose, or any implied warranty or condition arising out of a course of dealing, custom, or usage of trade. If the VinylFrog product does not conform to this warranty, then based on our discretion, the sole and exclusive remedy is either the replacement of the product or a refund of the purchase price.
Limitation of Liability
Except where prohibited by law, VinylFrog will not be liable for any loss or damage arising from its product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.
Durability
The durability of the product is based on exposure conditions in South China. Actual performance life will depend on substrate preparation, exposure conditions, and maintenance of the product. For instance, in areas with excessively high temperature, industrial pollution, or high altitude, exterior performance will decrease.
Recommendations
Recommended application tools:Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, sprayer, towel, and installation liquid Application method: Standard methods for Car Light Protection Film. Do not overstretch and overheat. Post heating is necessary. Post-heating temperature: 110°C flat surfaces, 130°C curves and overlaps. Aftercare: PH neutral. Avoid wax or solvents.
Produk Terkait
Clear Holographic Honeycomb Headlight Film with Air Channel Paper Liner